HEF4060 DATASHEET EPUB DOWNLOAD

HEF Datasheet, HEF PDF, HEF Data sheet, HEF manual, HEF pdf, HEF, datenblatt, Electronics HEF, alldatasheet, free. 15 Apr Data sheet acquired from Harris Semiconductor. SCHSC − Revised October HCDB consists of an oscillator section and CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator. CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator – CDB. Datasheet.

Author: Vomuro Mutilar
Country: Guadeloupe
Language: English (Spanish)
Genre: Life
Published (Last): 25 July 2014
Pages: 413
PDF File Size: 11.44 Mb
ePub File Size: 19.47 Mb
ISBN: 583-1-93202-208-1
Downloads: 47186
Price: Free* [*Free Regsitration Required]
Uploader: Kashicage

These kind of capacitors hef4060 datasheet have a bef4060 line on top of their body. My way of keeping this site alive. IC2 forms the time base oscillator and first pre-scaler stage.

This reset pulse is also used as carry to the hours counter. This not only prevents the clock hef4060 datasheet advancing every minute during SET mode, it also starts counting a whole new minute once hef4060 datasheet clock hef4060 datasheet set hef4060 datasheet RUN mode again.

This reset pulse is very short, because once it is high, the counters are reset and the reset pulse is gone again. I don’t need the output of the seconds counter itself, because I do not have a seconds display. IC4B tries to do the same for the 0. In SET mode the SET signal is high, and the seconds to minutes carry can never occur because the seconds counter is held in reset.

TP1 is a test point at which you can measure the buffered Now IC9D will inverse the pulses coming from the push button. Everything is built on pad board using Road Runner wiring to connect all the components together.

This allows you to accurately synchronize the clock with a known good time source. Both buttons have a debouncing capacitor in parallel to make sure that every button press results in just one pulse. This is a nice 0. Let’s start simple, the buttons, hef4060 datasheet are used to set the time.

While the clock is in run mode SET is high, opening the gate for the carry pulse. The oscillator hef4060 datasheet is built as described in the HEF data sheet.

It’s a bed side table clock, I don’t need it to light up the hef4060 datasheet room at night, you know. This will produce a high going reset pulse on the output of IC10B.

I have covered the time base and the counters here. It is spread over two sheets, one sheet covers the hef4060 datasheet base and the seconds, minutes and hwf4060 counters. You can download the circuit diagram here. And now hef4060 datasheet hours counter. Once the counters reach that state they are reset back to 0 again. As usual, with such a one of project, I didn’t bother to create a PCB for the project. We are only interested in two others, the Hz and the 64Hz outputs, which are used in the display section of the clock.

Please consider clicking on the Support Hef4060 datasheet button to show your appreciation.

Результаты поиска для HEF4060

This makes the output of IC10C constant low, except during hef4060 datasheet carry pulse. This signal is fed to the seconds counter, as described below.

In Run mode only the SET button will have any effect, the other 3 buttons are inhibited. Hef4060 datasheet the output of IC10C goes high when a button is pressed. We need 1Hz, not 2Hz, to feed to our seconds counter. It’s output Q0 of the first decade counter IC4A. Hef4060 datasheet the next page I’ll explain the display circuit and power supply of the clock. The Buttons Let’s start simple, the buttons, which are used to set the time. Together with this knowledge you should hef4060 datasheet able to build the clock yourself too.

Otherwise the roll over of the minutes counter would advance the hours counter too.

HEF datasheet, HEF datasheets, manuals for HEF electornic semiconductor part

This pulse is very short hef4060 datasheet datasheft cause is hef4060 datasheet by the reset almost instantly. This allows you to advance the hours counter. It is very important to use 0 tempco capacitor for C4. The CLK input to the flip-flop is low, because the hours counter has just been reset to 0. When the second decade reaches 6 the output of IC10A will go low.

OK, that’s enough hef4060 datasheet this one page. This pulse is used to flash the colon between the hour digits and the minute digits on vatasheet display.

Both inputs of IC10D are high when the button hef4060 datasheet pressed, making its output low. We haven’t talked about the carry from the seconds counter to the minutes counter yet.

CMOS 14-Stage Ripple-Carry Binary Counter/Divider and Oscillator

Its signal level is constantly low, with only a very short rising pulse hrf4060 the counter reaches 60 minutes. When the hours counter is reset, so is the flip-flop, making its Hef4060 datasheet output high. The Hardware Part 1 You can download the circuit diagram here. At the end it will produce an accurate frequency of 2Hz on output pin 3. What is Hef4060 datasheet doing there?

The Minutes Counter Next stop, the hef4060 datasheet counter. The carry from the seconds counter is constantly high, with only a short carry pulse every 60 seconds.

But when the most significant digit of the hours counter hef4006 the clock input of the flip-flop rises, which sets the hef4060 datasheet, making the Q output low. From then hef4060 datasheet the flip-flop remains in that state, until the hours counter is reset to 0 again.